TE
Termet 에러코드Termet error codes
50개 코드 · 1개 제품군50 codes · 1 categories
🔥보일러·온수기Boilers & Water Heaters 50
01불꽃 미감지No flame detected03과열 — 급수/환수 센서 100℃ 초과Overheating — supply/return sensor above 100℃05타코미터 오류 — 팬이 설정 회전수에 도달하지 못함Tachometer error — fan did not reach the set speed11센서 초기 점검 오류 — 펌프 가동 후 4분 내 난방/환수 NTC 온도가 5도 이내로 동조되지 않음Initial sensor check error — CH and return NTC temperatures fail to equalise within 5 degrees in 4 minutes13오류 리셋 과다(15분 내 5회)Too frequent fault resets (5 times within 15 minutes)15NTC 센서 온도 테스트 오류NTC sensor temperature test error16난방 NTC 센서가 배관에 접촉되지 않음CH NTC sensor not in contact with the pipe17환수 NTC 센서가 배관에 접촉되지 않음Return water NTC sensor not in contact with the pipe18난방 또는 환수 NTC 센서 구조 손상Structural damage of the CH or return NTC sensor2거짓 화염 — 가스밸브가 닫혀 있어야 할 때 화염 신호 감지False flame — flame signal detected while the gas valve should be closed21ADC 변환기 오류 — 제어기 교체 필요 가능성ADC converter error — controller likely needs replacement25마이크로프로세서와 EEPROM 소프트웨어 불일치 — 제어기 교체Software in microprocessor and EEPROM not identical — controller replacement required31난방 NTC 센서 회로 단선 또는 단락(직렬 연결된 과열제한기 작동이 원인일 수 있음)CH NTC sensor circuit open or shorted (may also be caused by the overheat limiter wired in series)32온수(CWU) NTC 센서 단락DHW NTC sensor circuit shorted33온수(CWU) NTC 센서 단선DHW NTC sensor circuit open34공급 전압 저하 — 157V(±10V) 미만Supply voltage dropped below 157 V (±10 V)37난방수 압력 과저 — 0.5bar 미만Heating water pressure too low — below 0.5 bar41수압센서 신호 대기시간 초과 — DSP/ESYS 통신 문제 가능Pressure sensor signal timeout — possible DSP/ESYS communication problem44환수 NTC 센서 회로 단선 또는 단락Return water NTC sensor circuit open or shorted45배기가스 온도센서 단락 — 배선 점검Flue gas temperature sensor shorted — check wiring46배기가스 온도센서 단선 — 배선 점검Flue gas temperature sensor circuit open — check wiring47수압 변환기 고장 또는 미연결Pressure transducer damaged or not connected7배기가스 과온 보호 — 약 10분 후 자동 복귀, 열퓨즈 손상 시 교체Flue gas over-temperature protection — auto-resume after about 10 minutes; replace thermal fuse if damaged8화염 감시 회로 내부 오류Internal flame-control circuit error80난방 NTC와 환수 NTC 센서가 서로 바뀌어 장착됨CH and return water NTC sensors swapped9가스밸브 제어 회로 오류Gas valve control circuit error99DSP 디스플레이와 ESYS 제어기 간 통신 불가(배선 점검, DSP/ESYS 교체)No communication between DSP display and ESYS controller (check wiring, replace DSP or ESYS board)E01버너 불꽃 없음 — 재점화 3회(LPG 2회) 실패 후 잠금. (동일 코드로 '가스 차단 상태에서 불꽃 오감지'도 표기됨)No burner flame — lockout after 3 failed reignition attempts (2 for LPG). (The same code is also used for 'false flame detection with the gas shut off')E02배기가스-물 열교환기 수온 95℃ 초과(과열) — 블로킹, 리셋 필요Water temperature in the flue gas/water heat exchanger exceeded 95°C — lockout, press resetE03(B형 개방식) 연도 부압 없음 또는 배기온도 제한기 회로 단선 — 가스밸브 차단 후 15분 대기·재시도, 실패 시 블로킹(Type B open-flue) No negative pressure in the chimney duct or break in the temperature limiter circuit — gas valve closes, 15-min wait and retry, lockout after failed attemptsE04난방수 NTC 온도센서 회로 손상(단락/단선) — 버너 정지Damage (short/open) in the central-heating water NTC temperature sensor circuit — burner shuts offE05난방수 흐름 없음(개방 회로 P7=0에서만 적용) — 흐름 부재 지속 또는 흐름센서 손상 시 240초 후 블로킹No heating water flow (applies only in open circuit, parameter P7=0) — permanent flow sensor damage or loss of flow causes lockout after 240 sE06보일러 전자제어(제어보드) 내부 회로 이상 — 버너 정지, 제어보드 교체 필요Fault in the boiler's electronic control system (internal control-board circuits) — burner off; control board replacement requiredE07가스밸브 모듈레이터 계통 고장 — 보일러는 최소 출력으로 운전 지속Fault in the gas valve modulator system — boiler keeps running at minimum powerE08난방수 압력 트랜스듀서 손상 — 버너 정지, 펌프 180초 후속운전Damaged central-heating water pressure transducer — burner off, pump runs on for 180 sE09난방(CO)회로 수압 이상 — 0.5bar 미만 또는 2.8bar 초과 시 버너 정지(0.5~2.5bar 복귀 시 자동 재개)Incorrect CH circuit pressure — burner off when P > 2.8 bar or P < 0.5 bar (auto-return when 0.5–2.5 bar)E10급탕(온수) 온도 NTC 센서 회로 손상 → 버너 정지Domestic hot water NTC sensor circuit damaged → burner shut offE13불꽃 감지 후 발생한 E1 비상상황 연속 최대횟수 초과 — 리셋 필요Maximum number of consecutive E1 emergency situations after flame detection exceeded — press resetE14PWM 펌프 모드 난방 중 환수(리턴) 난방수 센서 없음/손상Return heating-water sensor missing/damaged during CH operation with PWM pump activeE15PWM 펌프 모드 난방 중 환수(리턴) 난방수 센서 없음/손상Return heating-water sensor missing/damaged during CH operation with PWM pump activeE16팬 회전수 측정회로 또는 팬 자체 고장Fan speed measuring circuit or the fan itself failedE22EEPROM 메모리 오류 — 리셋 후 지속 시 서비스EEPROM memory error — press reset, call service if it persistsE31OpenTherm 통신 오류 — 실내온도조절기 전기 연결 확인OpenTherm communication error — check electrical connection to room thermostatE32확장기판과의 통신 오류Communication error with the expansion boardE41배기가스 온도센서 동작 불량Flue gas temperature sensor operating incorrectlyE44배기가스 온도센서 감지 온도 초과Temperature exceeded at the flue gas temperature sensorE46난방수압 변환기(압력센서) 손상 → 버너 정지, 펌프 180초 운전CH water pressure transducer damaged → burner off, pump runs 180 sE98전원 전압 이상 — 전압이 정상 복귀하면 자동 재가동Incorrect supply voltage — boiler resumes automatically when voltage returns to normalE99보일러 전자회로 고장 → 버너 정지, 리셋 후 지속 시 서비스Failure in boiler electronic system → burner off; reset, call service if it persistsL3에러 아님 — 난방수온이 설정보다 5℃ 초과 시 열교환기 냉각을 위한 3분 난방 일시정지 표시(정지 후 펌프 약 180초 후속운전)Not an error — 3-minute CH heating hold to cool the flue-gas/water heat exchanger after the heating water exceeds the setpoint by 5°C (pump runs on ~180 s)