노리츠 에러코드Noritz error codes
80개 코드 · 1개 제품군80 codes · 1 categories
🔥보일러·온수기Boilers & Water Heaters 80
002욕조 자동 온수받기 수위 설정 불량 — 빈 욕조 상태에서 첫 자동운전을 하지 않았거나 정전으로 수위 기억이 어긋남Bath auto-fill water level setting fault (first auto-fill not done with an empty tub, or level memory lost after a power outage)003난방 운전 중 정전 — 정전 복구 후 첫 난방 운전 시 표시Power outage during heating operation (shown on the first heating run after power is restored)011급탕을 60분 이상 연속 사용했을 때 나오는 알림 표시(고장 아님)Notice shown when hot water has run continuously for 60+ minutes (not a fault)012추가열(재가열)을 90분 이상 연속했을 때 나오는 안전장치 알림(고장 아님)Safety notice after 90+ minutes of continuous bath reheating (not a fault)032욕조 자동 온수받기가 규정 수위까지 차지 않음 — 배수전 잠금 누락, 순환 어댑터 필터 막힘, 추가열 배관 동결 등Bath auto-fill does not reach the set level — drain plug left open, clogged circulation adapter filter, or frozen reheat piping043난방수(부동액) 부족Low heating water (antifreeze)10연소 이상(플루 막힘 등)Air flow abnormality (unit shuts off)100석유 급탕기의 내진 자동소화장치 작동Earthquake auto shut-off device tripped (oil-fired water heaters)101급배기 이상 — 능력을 낮춘 상태로 운전(경고 표시)Intake/exhaust fault — unit runs at reduced capacity (warning)102급탕기 연소 이상 — 불꽃 감시 부품이 연소 불량을 검지(능력 저하 상태로 운전)Combustion fault detected by the flame-monitoring part (unit runs at reduced capacity)103난방 연소 이상 — 난방 기능이 있는 급탕기의 난방 연소 불량Heating combustion fault on a heating-capable water heater11점화불량 — 이그나이터·가스전자밸브·기판·점화플러그·플레임로드·버너 계통Ignition failure (initial flame fault detection)110점화 실패 — 연소제어장치가 불꽃을 검지하지 못함(연료 공급·점화계통 부품)Ignition failure — combustion controller did not detect flame (fuel supply or ignition-system parts)111급탕 점화 불량 — 연료(가스·등유) 미공급 또는 점화계통 부품 불량Hot-water ignition failure — no fuel supply (gas/kerosene) or faulty ignition parts112욕조(추가열) 점화 불량 — 연소가 도중에 멈춤, 연료 공급·불꽃검출 계통 확인Bath (reheat) ignition failure — combustion stopped; check fuel supply and flame-detection parts113난방·욕조 추가열 점화 불량 — 연소가 도중에 멈춤Heating/bath-reheat ignition failure — combustion stopped mid-cycle12연소 중도정지 — 급탕 점화 계통 부품 이상Flame Rod does not detect flame (flame fault detection)120연소가 도중에 멈춤 — 가스 공급 확인, 석유식은 등유 보급·에어빼기 후에도 지속되면 점화·염검출 계통 부품 불량Combustion stopped mid-cycle — check gas supply; on oil units refill kerosene and bleed air, otherwise ignition/flame-detection parts are faulty121급탕/욕조/난방 실화(실화) 안전장치 작동Flame Rod does not detect flame (flame fault detection)123난방이 연소하지 않음 — 가스 공급 문제 또는 등유 부족·송유관 공기 혼입Heating does not fire — gas supply issue, or kerosene shortage/air in the oil line130실내설치형 가스급탕기의 연소 불량(일산화탄소 농도 이상) — 즉시 환기 필요Indoor gas water heater combustion fault (abnormal CO level) — ventilate immediately14기기 내 과열방지 안전장치 작동Overheat Prevention Device (Thermal Fuse) triggered140기기 내부 이상 고온을 검지해 과열방지 안전장치가 작동Overheat protection device tripped after abnormally high internal temperature143연소하지 않음 — 연소 계통 부품 고장 가능성Unit does not fire — likely a faulty combustion-system part150온도 계통 부품 불량Temperature-system part fault151공회전(빈 연소) 방지장치 불량Dry-fire prevention device fault16출탕온도 이상 — 설정보다 높은 온도의 온수가 나옴(가스팬히터는 과열방지장치 작동)Outlet temperature abnormality — water hotter than the setpoint (on gas fan heaters, overheat protection tripped)161급탕 출탕온도 이상 — 설정온도보다 높은 온수가 나옴Hot-water outlet temperature fault — water hotter than the setpoint162자동 주탕(욕조 온수받기) 온도 이상 — 순환 어댑터 필터 막힘 등Auto bath-fill temperature fault — e.g. clogged circulation adapter filter170드레인 금구 역지밸브 이상 — 드레인 배수 기구 점검 필요Drain fitting check-valve fault — drain mechanism needs inspection171석유 급탕기 본체 관체(가마) 계통 불량 — 단수·배관 동결로도 표시될 수 있음Oil water heater tank/boiler-body system fault — can also appear on water outage or frozen piping173난방회로 누수 검지 — 난방 배관 누수 또는 배관 내 공기 잔류Heating circuit leak detected — leaking heating piping or trapped air190드레인 탱크 수위전극 이상 — 수위전극 커넥터 접속 점검 필요Drain tank water-level electrode fault — check the electrode connector193통신 코드(전장 배선) 불량Communication cable/wiring fault200연소·급배기 계통 이상으로 안전장치(공회전 방지장치 등) 작동Safety device tripped due to a combustion/venting fault (incl. dry-fire prevention)210배기 계통 불량 — 배기를 배출하지 못함Exhaust system fault — flue gas cannot be discharged252욕조 물 순환을 검지하는 수류 스위치 등의 불량Fault in the bath water-flow switch that detects tub circulation280기기 내 등유 잔량을 검지하는 부품(플로트 스위치 등) 불량Faulty kerosene level-detection part (float switch etc.)29드레인(응축수) 배관 동결·막힘 또는 중화장치 막힘(가스화 석유 열원기는 등유 잔량 검지 부품 불량)Condensate Container clogging290중화기 불량 또는 드레인 배수 막힘·동결Neutralizer fault, or clogged/frozen condensate drain291중화기 불량 또는 드레인 배수 막힘·동결Neutralizer fault, or clogged/frozen condensate drain31서미스터 이상(냉수/온수/열교환기 출구)Thermistor - Cold Water abnormality370연소 계통 센서 불량 또는 급배기구·연통 막힘Combustion sensor fault, or blocked intake/exhaust or flue390연소·배기 관련 센서 계통 부품 이상Combustion/exhaust sensor system fault410에코윌(가스 발전·급탕 시스템): 보조 열원측 유량을 측정하는 부품 등의 불량ECOWILL cogeneration system: fault in the part measuring flow on the backup heat-source side412자동 온수받기가 작동하지 않음 — 주탕 수량 센서 계통 불량Auto bath-fill does not work — fill flow-sensor fault430드레인 탱크 내 수량을 측정하는 부품 불량Faulty part measuring water volume in the drain tank432욕조 자동운전 중 운전이 정지 — 욕조를 비운 상태에서 자동운전을 다시 실행Bath auto-fill stopped mid-run — redo auto-fill with an empty tub510연소하지 않음 — 가스 통로 관련 부품(가스 전자밸브) 불량Unit does not fire — gas-passage part (gas solenoid valve) fault54오토바스 욕조 세정 시 물·온수 유로를 전환하는 밸브 불량Faulty flow-switching valve during auto-bath tub cleaning540중화기 관련 부품 불량 — 단수·배관 동결로도 표시될 수 있음Neutralizer-related part fault — can also appear on water outage or frozen piping543난방 운전 불가 — 난방수 누수 또는 난방 배관 공기 혼입Heating cannot run — heating water leak or air trapped in the heating piping56오소지욕조(자동 욕조세정): 단수 등으로 물이 공급되지 않음 — 단수 복구 후에도 지속되면 수리 필요Auto-bath-cleaning unit: no water supply (e.g. water outage); if it persists after supply returns, service is needed562자동 온수받기 계통 부품 불량, 또는 급수 배관 동결·단수Auto bath-fill system part fault, or frozen supply pipe / water outage563가스 난방겸용 급탕기(GTH 시리즈) 난방 시운전 시 표시되는 이상Fault shown during the heating test-run on GTH gas combi water heaters580기기 내 신호 통신 관련 불량Internal signal/communication fault61팬모터 이상Fan Motor abnormality610송풍기(연소용 팬) 계통 불량 — 급기·배기를 못 함Blower (combustion fan) system fault — cannot draw air or vent613난방측 송풍기(팬모터) 계통 불량Heating-side blower (fan motor) fault63욕조 순환 계통 불량 — 필터 청소·펌프 마중물 후에도 지속되면 부품 불량Bath circulation system fault — if it persists after filter cleaning/pump priming, a part is faulty632욕조 물이 순환하지 않음 — 수위 부족·필터 막힘·배관 동결, 해소되지 않으면 순환 계통 부품 불량Bath water not circulating — low level, clogged filter or frozen pipe; otherwise faulty circulation parts640급탕기 본체 기판 등의 불량Water heater main PCB fault642욕조 펌프 계통 부품 불량으로 자동 온수받기·추가열 불가Bath pump system fault — auto-fill and reheat unavailable643난방 펌프 또는 순환회로를 여닫는 부품 불량Heating pump or circulation-valve fault651온수받기 수량을 조절하는 부품(수량 서보) 불량Water-flow servo (fill volume control) fault652자동 주탕 불가 — 수량 조절 부품 불량Auto bath-fill impossible — flow-adjustment part fault661온수·냉수를 혼합하는 부품(바이패스 수량서보·분배밸브) 불량 — 설정보다 높은 온도의 물이 나올 수 있음Hot/cold mixing part (bypass flow servo / distribution valve) fault — water can be hotter than the setpoint700리모컨과 급탕기 본체 간 통신 불량Communication fault between the remote controller and the water heater710급탕기 내부 부품(연소제어 회로 계통) 불량Internal part fault (combustion control circuit)720본체 내부 연소 계통 부품 불량Internal combustion-system part fault73급탕기기 에러 표시(상세 미열람)Circuit Board setting abnormality (improper maintenance writers settings)731기판·통신 계열Circuit Board setting abnormality (improper maintenance writers settings)760급탕기 본체 통신 불량(리모컨 전송 이상)Water heater communication fault (remote controller transmission)800기기 내부에서 등유가 새는 것으로 판단해 안전장치(오일 센서) 작동Oil sensor tripped — kerosene may be leaking inside the unit88설계상 표준사용기간(가정용 10년·업무용 3년) 도달 — 점검시기 알림(고장 아님)Design service life reached (10 years household, 3 years commercial) — inspection reminder, not a fault90연소 이상(3회 미달)Air flow abnormality (unit shuts off)92중화기 수명 임박 알림 — 교체 필요(방치하면 93/930으로 바뀌며 급탕 정지)Neutralizer nearing end of life — replace it (it later changes to 93/930 and the unit stops)920중화기 수명 임박 알림 — 방치하면 930으로 바뀌며 급탕 정지Neutralizer nearing end of life — becomes 930 and the unit stops if ignored930중화기 수명 종료 — 교체 필요(기기 정지)Neutralizer life over — replacement required (unit stops)992불꽃 감시 부품이 연소 불량을 검지(GTS-164 시리즈) — 급배기 불량·가스 조정 불량Flame-monitoring part detected abnormal combustion (GTS-164 series) — venting or gas adjustment problem