Midea 에러코드Midea error codes

118개 코드 · 5개 제품군118 codes · 5 categories

🍳주방가전Kitchen Appliances 38

E-01컴팩트 오븐: 온도센서 단선 보호Compact oven: temperature sensor open-circuit protection E-04컴팩트 오븐: 온도센서 단락 보호Compact oven: temperature sensor short-circuit protection E-05스팀오븐: 급수(물) 계통 이상Steam oven: water system abnormal E-06스팀오븐: 물탱크가 제대로 닫히지/장착되지 않음Steam oven: water tank not closed/installed properly E-1마이크로웨이브 인버터 IB 신호 이상 — 기동 전 과대 신호 검출Microwave inverter IB feedback signal abnormal (excessive signal detected before start-up)E-11컴팩트 오븐: 버튼이 60초 이상 계속 눌림Compact oven: a key detected as pressed for more than 60 seconds E-17컴팩트 오븐: 예열 실패 보호(예열 온도 미도달)Compact oven: preheating failure protection (preheat temperature not reached)E-3전동 자동문(오토 도어) 개폐 시스템 이상 — 부저 8회 후 코드 표시Electric auto-door opening system failure (buzzer sounds 8 times, code displayed)E-5마이크로웨이브 동작 중 인버터 IB 신호 9초간 미검출Inverter IB signal not detected for 9 seconds during microwave operation E-6마이크로웨이브 동작 중 IB 신호가 정상 출력의 200% 초과IB signal exceeds 200% of normal microwave output E-8마이크로웨이브 동작 중 IB 신호가 정상 출력의 50% 미만IB signal below 50% of normal microwave output E01오븐 온도센서 단선/단락 — 냉각팬 외 전 부하 정지Oven temperature sensor open/short circuit; all loads stop except the cooling fan E02파이롤리틱 자동청소 중 온도 검증 오류 — 도어 잠금Temperature verification error during pyrolytic self-cleaning; the door is locked E03마이크로웨이브 자동메뉴 실행 중 온도센서 단선/단락 검출Temperature sensor open/short detected while running the microwave auto menu E04표시보드-전원보드 통신 5초 이상 두절No communication data between display board and power board for 5 seconds E05미트 프로브(온도 탐침) 단락 — 프로브 메뉴 실행 시 표시Meat probe short circuit (displayed when running the meat probe menu)E08가열 이상 — 조리 중 10분간 온도 변화 3℃ 미만(온도센서/전원보드/히터)Heating fault: temperature varies less than 3°C over 10 minutes of cooking (sensor / power board / heater)E09제어칩 오류 감지 — 도어 잠금 후 부하 정지Control chip error detected; door locked and loads shut off E1식기세척기: 급수 시간 초과Dishwasher: water filling exceeds preset time E17캐비티(조리실) 가열 이상Cavity heating abnormal E3식기세척기: 가열 시간 초과Dishwasher: heating exceeds preset time E4식기세척기: 넘침(오버플로우)Dishwasher: overflow E6식기세척기: 서미스터 단선Dishwasher: open-circuit failure of thermistor E7식기세척기: 서미스터 단락Dishwasher: short-circuit failure of thermistor E8식기세척기: 전환(디버터) 밸브 이상Dishwasher: diverter valve fault E9식기세척기: 버튼이 장시간 눌림(터치 모델)Dishwasher: button pressed for a long time (touch control models)EC식기세척기: BLDC 모터/제어 이상(BLDC 모델)Dishwasher: BLDC motor failure (models with BLDC)Ed식기세척기: 메인보드-표시보드 통신 이상Dishwasher: communication failure between main control board and display board EF식기세척기: 물탱크 수위 이상(플로트 스위치 미동작)Dishwasher: water tank level abnormal (float switch does not move)Er-1G2 오븐: 온도센서 단선 — 전 부하 정지G2 oven: temperature sensor open circuit; all loads stop Er-2G2 오븐: 온도센서 단락 — 전 부하 정지G2 oven: temperature sensor short circuit; all loads stop Er-3G2 오븐: 미트 프로브 센서 단락G2 oven: meat probe sensor short circuit Er-4G2 오븐: 오븐 중심 온도 300℃ 초과 — 조리 취소·도어 잠금G2 oven: oven centre temperature above 300°C; cooking cancelled and door locked Er-5파이롤리틱 청소 중 온도 상승 부족(200℃ 도달 후 10분간 270℃ 미만)Pyrolytic mode: temperature still below 270°C ten minutes after reaching 200°C Er-6파이롤리틱 청소 중 도어 잠금 실패(300℃ 초과에도 잠기지 않음)Pyrolytic mode: door lock not engaged even above 300°C; heating stopped Er-7파이롤리틱 모델: 메인 칩이 전원(전류)을 감지하지 못함 — 전 부하 정지Pyrolytic models: main chip does not detect electricity; all loads stop F11캐비티(조리실) 과열 이상Cavity overheat abnormal FI LLF1F1

🌀세탁기·건조기Washers & Dryers 28

C8통돌이(탑로딩) 인버터 구동보드-제어보드 통신 이상Top-load washer: communication failure between inverter drive board and control board E1Water inlet errorDishwasher: water filling exceeds pre-set time — inlet valve open 4 minutes but water quantity not reached.E10Water inlet errorWater injecting problem during wash cycle — water level does not change within 3 minutes.E12Water overflow errorWater level in the drum exceeds the overflow level.E2통돌이(탑로딩) 배수 이상 — 설정 시간 내 배수 미완료Top-load washer drain error: drainage not completed within the set time E20건조기 배수 계통 이상 — 응축수 물통 만수 감지Dryer drain system error: water box detected full E21Drain ErrorOver-time water draining — water level does not change within 6 minutes.E3Lid Cover Open ErrorDishwasher: heating exceeds pre-set time — heating element working 60 minutes but water temperature not reached.E30Heating system errorDoor is not closed properly — door failed to lock more than 3 times.E32건조기 습도센서 값 범위 이탈Dryer humidity sensor value out of range E33NTC (temperature sensor) errorWater level sensor problem — sensor frequency out of normal range for 10 seconds.E34드럼 수온 이상 — 수온센서(NTC) 고장Water temperature in the drum abnormal / water temperature sensor failure E35드럼 수온 이상 — 수온센서(NTC) 고장Water temperature in the drum abnormal / water temperature sensor failure E36가열 이상 — 10분 가열해도 온도 상승 3℃ 미만Heating error: temperature rises less than 3°C after 10 minutes of heating E37건조 입구(dry-in) 서미스터 단선/단락Dryer inlet (dry-in) thermistor open or short circuit E38건조 출구(dry-out) 서미스터 단선/단락Dryer outlet (dry-out) thermistor open or short circuit E3A건조 불량 — 건조 중 온도 상승 3℃ 미만(건조 히터/서모스탯 계통)No drying: temperature rises less than 3°C during the drying process (dry heater/thermostat circuit)E4Spin Unbalance ErrorDishwasher: overflow — overflow micro-switch active for longer than 2 seconds.E50Motor Start ErrorMotor inverter PCB detects abnormal signals.E58인버터(주파수) 보드 모터 과부하 또는 모터 결상Frequency board motor overload or motor open phase E60Motor ErrorThe motor does not rotate — motor failed to start 5 times.E61Motor ErrorThe PCB cannot detect the speed feedback signal 5 times (speed measured below 15 rpm for 3 seconds).E62Motor ErrorActual motor speed is 300 rpm higher than the target speed.E64Inverter motor communication errorMotor inverter PCB error — poor communication between main PCB and motor inverter PCB (BLDC models only).E7Brake Abnormal Error CodeDishwasher: short-circuit failure of thermistor.E80Display PCB to Main PCB communication errorCommunication error — no communication between main control board and display panel.F8통돌이(탑로딩) 수위센서 신호 이상(주파수 이상)Top-load washer water level sensor signal fault (frequency out of range)Fd통돌이(탑로딩) 도어록 이상Top-load washer door lock fault

❄️에어컨Air Conditioners 24

E0EEPROM 파라미터 오류EEPROM parameter error E1실내-실외 통신 이상Room temperature sensor error E2제로크로싱 검출 오류(전원 위상)Evaporator temperature sensor error E3실내 팬 속도 이탈(회전수 제어불능)Condenser temperature sensor error (select models)E4실내 온도센서(T1) 이상Display panel communication error E5증발기 코일센서(T2) 이상Evaporator coil sensor (T2) fault E6실내 온도센서(T1)·증발기 코일센서(T2) 단선/단락Indoor room temp sensor (T1) / evaporator coil sensor (T2) open or short circuit E8트윈(마스터-슬레이브 실내기) 통신 이상Communication error between master and slave unit (twins system)EC냉매 누설 감지 (실내기에 EC 표시)Refrigerant leakage detection (indoor unit displays EC)EE카세트/덕트형 배수 수위 경보Cassette/duct-type drain water level alarm F0과전류 보호Overcurrent protection F1실외 외기온센서(T4) 이상Outdoor ambient temperature sensor (T4) fault F2응축기 코일센서(T3) 이상Condenser coil sensor (T3) fault F3압축기 토출온도센서(T5) 단선/단락Compressor discharge temperature sensor (T5) open or short circuit F4실외 EEPROM 파라미터 오류Outdoor EEPROM parameter error F5실외 팬 속도 이탈Outdoor fan speed out of range F6실외 T2B 온도센서 단선/단락T2B temperature sensor open or short circuit P0IPM 이상 / IGBT 과대전류IPM fault / IGBT overcurrent P1모델차: 바닥트레이 만수Bottom tray is full P2IPM/압축기 상부 고온 보호IPM/compressor top high-temperature protection P3외기온 과저(저온보호)Outdoor temperature too low (low-temperature protection)P4인버터 압축기 구동 오류Inverter compressor drive error P5실내기 운전모드 충돌(멀티 실외기 연결 시)Indoor units mode conflict (multi outdoor unit systems)P6압축기 저압 보호Compressor low pressure protection

🧊냉장고Refrigerators 22

C9제빙실 온도센서 이상Ice-making compartment temperature sensor failure CACommunication failure between Main PCB and Power PCBCommunication failure between main PCB and the display PCB in the door.CC제빙실 제상(디프로스트) 센서 이상Defrost sensor of the ice-making compartment failure E0Freezer ice maker horizontal initialization failureThe ice maker can not be reset normally.E1냉장실 온도센서 이상Refrigerating chamber temperature sensor failure E2냉동실 온도센서 이상Freezer temperature sensor failure E3칠러/변온실 온도센서 이상Chiller drawer / flex chamber temperature sensor failure E4Defrost sensor in the refrigerating chamber failsThere is a problem with the defrost sensor.E5Defrost sensor in the freezing chamber failsThere is a problem with the defrost sensor.E6Main control PCB and Display control PCB communication failsCommunication failure between main PCB and display PCB.E7Ambient temperature sensor failsThere is a problem with the ambient temperature sensor terminals or the sensor circuit.E8Defrost sensor in chiller or flex drawer/chamber failsThere is a problem with the defrost sensor terminals or the sensor circuit.E9High temperature alarm in the chamberHigh temperature alert.Ed도어 열림 경보 — 문이 120초 이상 열림Door not closed alarm: door open for more than 120 seconds EEFreezer ice maker temperature sensor failureThere is a problem with the sensor terminals of the ice maker or the sensor circuit.EFWater tank installation failureCircuit fault of water tank is not installed right in place.EHHumidity sensor failsThere is a problem with the humidity sensor or the sensor circuit.EL고내 저온 경보 — 설정 온도보다 낮음Low temperature alarm in the chamber EPFreezer ice maker ice-flipping failureThere is a problem with the ice maker.F4냉장실 제빙기 온도센서 이상Refrigeration ice maker temperature sensor failure F5냉장실 제빙기 이빙(얼음 배출) 실패Refrigeration ice maker ice-flipping failure F6냉장실 제빙기 수평 초기화 실패Refrigeration ice maker horizontal initialization failure

💨에어케어Air Care 6

AS습도센서 이상Humidity sensor error E3제품 고장(malfunction)Unit malfunction Eb물통 분리/오장착(펌프형)Bucket removed or not seated in the right position EC제습기: 냉매 누설 감지Dehumidifier: refrigerant leakage detection ES증발기 튜브 온도센서 이상Evaporator tube temperature sensor malfunction P2물통 가득/오장착(무펌프형)Bucket full or bucket not in the right position