Junkers 에러코드Junkers error codes
29개 코드 · 1개 제품군29 codes · 1 categories
🔥보일러·온수기Boilers & Water Heaters 29
A1난방수 압력 부족으로 순환펌프가 공회전(건식 운전)했습니다. 시스템 충전압이 1.2bar 미만인지 확인 대상입니다.Modulating pump has run dry (system fill pressure too low).A2연소실에서 배기가스가 새어 나오는 것이 감지되었습니다.Flue gas escaping at the combustion chamber.A3역풍방지기(연도 안전장치) 쪽 배기 온도센서(NTC)가 단선되었습니다.Flue gas NTC at the draught diverter is open-circuit.A4역풍방지기(연도 안전장치)에서 배기가스가 새어 나오는 것이 감지되었습니다.Flue gas escaping at the draught diverter.A5온수 저장탱크 온도센서 2(Speicher-NTC 2)가 고장입니다.Cylinder NTC 2 defective.A6연소실 배기 온도센서(NTC)가 단선되었습니다.Flue gas NTC at the combustion chamber is open-circuit.A7온수 온도센서(NTC)가 고장입니다(단선 또는 단락).Domestic hot water NTC defective (open circuit or short).A8보일러와 실내조절기(컨트롤러) 사이 CAN 통신이 끊겼습니다.CAN communication between the boiler bus module and the controller interrupted.AC확장 모듈이 인식되지 않습니다.Module not detected.Ad온수 저장탱크 온도센서 1(Speicher-NTC 1)이 인식되지 않습니다.Cylinder NTC 1 not detected.b1기기 사양을 지정하는 코딩 플러그가 인식되지 않습니다.Coding plug not detected.C1송풍기(팬) 회전수가 너무 낮습니다.Fan speed too low.C2고속 운전 중 배기 압력스위치 접점이 열렸습니다.Air pressure switch contact opens during operation at high fan speed.C4배기 압력스위치 접점이 열리지 않습니다.Air pressure switch contact does not open.C6배기 압력스위치 접점이 열린 상태로 유지됩니다.Air pressure switch contact remains open.CC외기 온도센서가 인식되지 않습니다.Outdoor temperature NTC not detected.d1LSM(안전 모듈)이 잠김 상태입니다. 온도감시기 등 외부 안전장치가 작동했습니다.LSM locked out (external safety device such as temperature limiter tripped).d3단자 8-9 사이의 점퍼(브리지)가 인식되지 않습니다(단자 개방).Bridge/jumper across terminals 8-9 not detected (terminal open).E0제어기판 내부 오류입니다.Internal fault on the PCB.E2난방 출수(공급) 온도센서(NTC)가 고장입니다(단선 또는 단락).Flow temperature NTC defective (open circuit or short).E5버너 출수 온도센서에서 과열 감지되어 안전 차단되었습니다.Safety cut-out triggered by the burner flow NTC (overheat).E7버너 쪽 출수 온도센서(NTC)가 단선 또는 단락되었습니다.Flow NTC at the burner is open-circuit or short-circuited.E8최저 수압 감시 스위치가 작동했습니다(난방수 압력 부족).Minimum pressure switch has tripped.E9안전 온도 제한기(STB)가 작동해 기기가 잠겼습니다(과열).Safety temperature limiter (STB) has tripped.EA운전 중 불꽃이 감지되지 않습니다(이온화 전류 없음). 가스 공급·응축수 배출·배기 막힘이 원인일 수 있습니다.Flame not detected during operation (no ionisation current).F0제어부 내부 오류입니다.Internal fault.F7기기가 꺼져 있는데도 불꽃이 감지됩니다(잘못된 이온화 신호).Flame detected although the appliance is switched off (false ionisation signal).FA가스 차단 후에도 불꽃이 계속 감지됩니다(이온화 전류 잔류).Flame still detected after the gas supply has been shut off.FC텍스트 디스플레이가 인식되지 않습니다.Text display not detected.